PE50BB-DIF-C

PE50BB-DIF-C

The PE50BB-DIF-C is a pyroelectric energy meter with a removable diffuser that is spectrally flat with diffuser off. It has a 46mm aperture with diffuser out and 33mm aperture with diffuser in. It can measure energies from 0.1mJ up to 40J. It can operate at repetition rates up to 40Hz and is calibrated from 0.19 – 20µm with diffuser off and for 0.532, 1.064 and 2.1µm with diffuser on. The sensor comes with a standard 1.5 meter cable for connecting to a meter or PC interface.

Please contact us for further information on this product.

 
  • Broadband (BB) with removable diffuser
  • Ø46mm, Ø33mm with diffuser
  • 0.19-20µm, 0.4-2.5µm with diffuser
  • 0.1mJ-40J
  • 40Hz
  • Ø62 W x 29 D (mm)
  • 40J
  • 10W/cm²
  • 20 ms
  • 0.3J/cm²
  • 2J/cm²
  • 10W
Scope Adapter

Scope Adapter

Plugs in between the PE sensor and power meter. Provides BNC output to scope to see every pulse up to the maximum frequency of the sensor.

Heat Sink

Heat Sink

Heat sink that screws onto rear of PE-C series sensors allowing working at over 50% higher average powers

SC Fiber Adapter

Sc Fiber Adapter

This fiber adapter is used for connecting power and energy sensors to a standard SC-type fiber. Many sensors need an additional mounting bracket to connect to all fiber adapters. More information can be found in the datasheet below.

ST Fiber Adapter

This fiber adapter is used for connecting power and energy sensors to a standard ST-type fiber. Many sensors need an additional mounting bracket to connect to all fiber adapters. More information can be found in the datasheet below.

FC Fiber Adapter

FC Fiber Adapter

This fiber adapter is used for connecting power and energy sensors to a standard FC-type fiber. Many sensors need an additional mounting bracket to connect to all fiber adapters. More information can be found in the datasheet below.

SMA Fiber Adapter

SMA Fiber Adapter

This fiber adapter is used for connecting power and energy sensors to a standard SMA-type fiber. Many sensors need an additional mounting bracket to connect to all fiber adapters. More information can be found in the datasheet below.

PE9/PE10/PE25 Fiber Adapter Bracket

PE9/PE10/PE25-C Fiber Bracket

A mounting bracket is needed to connect most power and energy sensors to a fiber adapter (SC, ST, FC or SMA). This bracket can be used for pyroelectric energy sensors in the PE9, PE10 and PE25 series. It is not compatible with diffuser-equipped sensors.

Beam splitter for PE and Thermal sensors

Beam Splitter Assembly for Pyro

Beam Splitter Assembly to measure pulsed laser sources too energetic for direct measurement. The reading with the Beam Splitter can be calibrated by setting the laser to a lower energy that will not damage the sensor and then taking a measurement with the beam splitter and without and taking the ratio.

PE Test Plates (metallic)

Damage Threshold Test Plates (metallic)

Test plates with same absorber coating as the sensor. For testing that laser beam is not above damage threshold (1such plate is included with sensor package).

Nova PE-C Adapter

Nova PE-C Adapter

The adapter plugs between the Nova D15 socket and the smart plug of the PE-C sensor to allow the Nova to operate with PE-C series sensors. See PE-C spec sheet for details.

PE-C to PE Size Adapter

PE-C to PE Size Adapter

The newer PE-C series sensors have a φ62mm diameter. The older PE series sensors have a φ85mm diameter. This adapter allows using the PE-C type sensors in jigs and setups that were originally designed for PE sensors.

3m Cable

3m Cable

3m cable to connect sensor to power meter or interface. Order along with sensor to receive this instead of the standard 1.5m cable.

Cable

5m Cable

5m cable to connect sensor to power meter or interface. Order along with sensor to receive this instead of the standard 1.5m cable.

10m cable

10m Cable

10m cable to connect sensor to power meter or interface. Order along with sensor to receive this instead of the standard 1.5m cable.